#Bmw ista/p 3.59 k+dcan e65 series
#Bmw ista/p 3.59 k+dcan e65 tv
#Bmw ista/p 3.59 k+dcan e65 windows

#Bmw ista/p 3.59 k+dcan e65 series

Start ISTA/P from the ISSS jumpgate by selecting вЂњProgramming, Coding,В IndividualizationвЂќ.ДЄ maximum of three vehicles or one model series F01/F02 vehicle can be programmedВ and encoded with ISTA/P on an ISSS.

#Bmw ista/p 3.59 k+dcan e65 tv

Note:В control modules that do not assume sleep mode (rest state) can causeВ closed-circuit current faults!Д¬heck all noted radio and TV frequencies as well as navigation destinations andВ store manually if necessary.ДЈвЂ“ Workshop System Management (WSM) button Park vehicle for at least 5 minutes (BN2000 and BN2020 vehicles) or 16 minutesВ (I-bus vehicle) with terminal R OFF so that all control modules can assume sleepВ mode, i.e. Perform vehicle test with the ISTA workshop system and end vehicle test onВ completion. Confirm the finishing off jobs individually.Д®nter the time and date information to ensure correct calculation of the CBSВ values in the vehicle.ДЄfter programming, reinstall all removed or disconnected data media (DVD,В iPodВ®, etc.) and check.Д¬ompare the previously printed or noted CBS data of the control modules and,if necessary, reset and correct as part of the vehicle test in the ISTA workshopВ system. in the vehicle test in the ISTA workshop system as defined in theВ final report. Perform the finishing off procedures such as calibration, initialization, serviceВ functions etc. Fault codes may be entered and MOST control modulesВ may be registered incorrectly if the ICOM is not correctly disconnected from theВ MOST direct access port. If an ICOM is connected to the MOST direct access port, disconnect the MOSTВ direct access port when requested to do so by the ISTA/P system, remove theВ ICOM from the MOST ring and close the MOST ring with the original flash plugВ (bridge) in the vehicle. CAS)ДЈ.Do not cut the connection between workshop network, vehicle interface andВ vehicleД¤.Close the boot lid again after any action in the luggage compartment (e.g.В loading/removing navigation DVD) to prevent the luggage compartment lightingВ from overheatingДҐ.During programming, perform no other activities on/in the vehicle than thoseВ instructed by ISTA/P.ДЎ.Execute procedure for finishing off the measures plan and confirm byВ clicking вЂњOKвЂќ Data media in a drive or still connected could cause programming toВ abortДЎ9.Before starting vehicle programming, make sure the boot lid is closed (to preventВ the luggage compartment lighting from overheating).ДЎ.Observe and follow requests and instructions in ISTA/PДў.Leave ignition switched on and follow instructions in ISTA/P (e.g. Make sure that the driverвЂ™s door contact is notВ operated during the programming procedure.ДЎ5.Perform a vehicle test with the ISTA workshop system to make sure that allВ installed control modules respond and any fault memory entries are read outДЎ6.Before programming, rectify any faults that may be present and delete any faultВ codes storedДЎ7.Determine CBS data, note down and end ISTA workshop systemДЎ8.Preparations: Remove inserted data media (DVD) and disconnect connected dataВ (iPodВ®, etc.). Terminal 15 is permanently switched on by pressing theВ START-STOP button. в€’ On vehicles with automatic terminal 15 shutdown (as from 03/2007) theВ signal from the door contact switches off terminal 15 by opening and closingВ the driverвЂ™s door.

в€’ If the vehicle model does not have an ignition lock, the identificationВ transmitter must be located in the vehicle interior. The coding procedure may be terminated if theВ identification transmitter is not inserted in the ignition lock. в€’ On vehicles with Comfort Access, the identification transmitter must beВ inserted in the ignition lock.

#Bmw ista/p 3.59 k+dcan e65 windows

Cables routed through open windows could be damagedВ when the windows are started automatically. Make sure that the vehicleВ system voltage does not drop below 13.0 volts while programming is in progressДЎ2.Set up connection between workshop network, vehicle interface and vehicleДЎ3.Check cable routing. LowВ system voltage may cause programming to cancel.

Please refer to the operatingВ instructions for the battery chargerДЎ1.Do not connect or disconnect the battery charger during programming. The battery charger connected during programming must be run in вЂњexternalВ power supply mode with battery connectedвЂќ.

Make sure that the wipers can move freelyД©.Make a note of all stored radio and TV frequencies as well as the navigation destinationsДЎ0.Connect up a BMW Group-approved battery charger in the engine compartment. The wipers may be actuated duringВ programming and initialization. 5.Activate electromechanical parking brake or apply parking brakeД¦.Make sure that the temperature of the transmission fluid is between -40 вЊВ (-40 вЏ) and 85 вЊ (185 вЏ)Д§.Switch off all electric loads, lights and turn signal lampsДЁ.Switch off wiper/washer system.